Call

 

Are you currently on the lookout for content concerning How to Install a Bathtub Yourself?

Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably challenging job. If the old tub is easily obtainable, the task can move immediately; if you have to open a wall to eliminate the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will require an assistant to move out the old tub and embeded in the new one. Make certain you have qualified yourself for the job and also fit attempting it. Rather than working with a contractor to take control of a halfway-completed project, it is better to consider using one before you start. Chances are you might require a specialist plumber to make tube connections.
This short article will aid you install a new tub in your restroom if you have actually currently acquired a new tub as well as don't need to alter the arrangement of your previous water supply pipes.
Your devices as well as material list ought to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted access that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the staying water that will come from the pipes. When the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will require lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in location between the tap as well as the sink. Safeguard the tap in place with the producer offered backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet ports. The former type needs to be attached to the tap ends first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Installing the Tub

Using the two wood boards under its feet, put the bath tub in the needed placement. The wood boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the bath tub till the level checks out degree.
To install faucets, fit the bottom of the outermost flexible tap adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the water supply and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Load the bathtub as well as additionally check the overflow electrical outlet and also the typical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub should wait till the bath tub has been used at the very least once as this will certainly resolve it right into its final placement.

 

 

Getting ready for the Installment

To start with, the supporting structure supplied with the bath should be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its final placement.

 

 

Tiling Around the Bath tub

In the area where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bathroom and also the tiling, leading to difficulties with dampness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and also installations. They are marketed in tubes and also cartridges, and also can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub remains in usage. The sealant can crack relatively very early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly available on the market. It is recommended to fit the floor tiles making use of waterproof or waterproof sticky and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a fervent person who reads on Installing A Bathtub, I thought sharing that information was a smart idea. So long as you enjoyed reading our article if you please be sure to share it. Thank-you for taking the time to read it.

Request Service